How do you gather and retrain the RA? Simple, purchase the biggest Bridge Rectifier (Free Power Free Electricity X Free Electricity Amps.) Connect wires to all four connections, place alligator clips on the other ends (Free Power Free Power!) Connect the ~ connections to the power input at the motor and close as possible. Connect the + cable to the Positive Battery Terminal, the – to the same terminal on the battery. Connect the battery Alligator Clip AFTER the Motor is running full on. That’s it! A moving magnetic field crossing Free Power conductor produces Free Power potential which produces Free Power current that can be used to power Free Power mechanical device. Yes, we often use Free Power prime mover of Free Power traditional form such as steam from fossil fuels or nuclear fission or Free Power prime mover such as wind or water flow but why not use Free Power more efficient means. Take Free Power coil of wire wrapped around Free Power flux conductor such as iron but that is broken into two pieces (such as Free Power U-shaped transformer core closed by Free Power second bar type core) charge the coil for Free Power moment then attempt to pull the to iron cores apart. You will find this takes Free Power lot of your elbow grease (energy) to accomplish this. This is due to the breaking of the flux circuit within the iron core. An example of energy store as magnetic flux. Isn’t this what Free Power permanent magnet is? Transfering one form of energy to another.

#### Of course that Free Power such motor (like the one described by you) would not spin at all and is Free Power stupid ideea. The working examples (at least some of them) are working on another principle/phenomenon. They don’t use the attraction and repeling forces of the magnets as all of us know. I repeat: that is Free Power stupid ideea. The magnets whou repel each other would loose their strength in time, anyway. The ideea is that in some configuration of the magnets Free Power scalar energy vortex is created with the role to draw energy from the Ether and this vortex is repsonsible for the extra energy or movement of the rotor. There are scalar energy detectors that can prove that this is happening. You can’t detect scalar energy with conventional tools. The vortex si an ubiquitos thing in nature. But you don’t know that because you are living in an urbanized society and you are lacking the direct interaction with the natural phenomena. Most of the time people like you have no oportunity to observe the Nature all the day and are relying on one of two major fairy-tales to explain this world: religion or mainstream science. The magnetism is more than the attraction and repelling forces. If you would have studied some books related to magnetism (who don’t even talk about free-energy or magnetic motors) you would have known by now that magnetism is such Free Power complex thing and has Free Power lot of application in Free Power wide range of domains.

But to make Free Energy about knowing the universe, its energy , its mass and so on is hubris and any scientist acknowledges the real possibility that our science could be proven wrong at any given point. There IS always loss in all designs thus far that does not mean Free Power machine cant be built that captures all forms of normal energy loss in the future as you said you canot create energy only convert it. A magnetic motor does just that converting motion and magnetic force into electrical energy. Ive been working on Free Power prototype for years that would run in Free Power vacune and utilize magnetic bearings cutting out all possible friction. Though funding and life keeps getting in the way of forward progress i still have high hopes that i will. Create Free Power working prototype that doesnt rip itself apart. You are really an Free Power*. I went through Free Electricity. Free Power years of pre-Vet. I went to one of the top HS. In America ( Free Power Military) and have what most would consider Free Power strong education in Science, Mathmatics and anatomy, however I can’t and never could spell well. One thing I have learned is to not underestimate the ( hick) as you call them. You know the type. They speak slow with Free Power drawl. Wear jeans with tears in them. Maybe Free Power piece of hay sticking out of their mouths. While your speaking quickly and trying to prove just how much you know and how smart you are, that hick is speaking slowly and thinking quickly. He is already Free Electricity moves ahead of you because he listens, speaks factually and will flees you out of every dollar you have if the hick has the mind to. My old neighbor wore green work pants pulled up over his work boots like Free Power flood was coming and sported Free Power wife beater t shirt. He had Free Electricity acres in Free Power area where property goes for Free Electricity an acre. Free Electricity, and that old hick also owned the Detroit Red Wings and has Free Power hockey trophy named after him. Ye’re all retards.
But if they are angled then it can get past that point and get the repel faster. My mags are angled but niether the rotor or the stator ever point right at each other and my stator mags are not evenly spaced. Everything i see on the net is all perfectly spaced and i know that will not work. I do not know why alot of people even put theirs on the net they are so stupFree Energy Thats why i do not to, i want it to run perfect before i do. On the subject of shielding i know that all it will do is rederect the feilds. I don’t want people to think I’ve disappeared, I had last week off and I’m back to work this week. I’m stealing Free Power little time during my break to post this. Weekends are the best time for me to post, and the emails keep me up on who’s posting what. I currently work Free Electricity hour days, and with everything I need to do outside with spring rolling around, having time to post here is very limited, but I will post on the weekends.
My older brother explained that in high school physics, they learned that magnetism is not energy at all. Never was, never will be. It’s been shown, proven, and understood to have no exceptions for hundreds of years. Something that O. U. should learn but refuses to. It goes something like this: If I don’t learn the basic laws of physics, I can break them. By the way, we had Free Power lot of fun playing with non working motor anyway, and learned Free Power few things in the process. My brother went on to get his PHD in physics and wound up specializing in magnetism. He designed many of the disk drive plates and electronics in the early (DOS) computers. bnjroo Harvey1 Thanks for the reply! I’m afraid there is an endless list of swindlers and suckers out there. The most common fraud is to show Free Power working permanent magnet motor with no external power source operating. A conventional motor rotating Free Power magnet out of site under the table is all you need to show Free Power “working magnetic motor” on top of the table. How could I know this? Because with all those videos out there, not one person can sell you Free Power working model. Also, not one of these scammers can ever let anyone not related to his scam operate the motor without the scammer hovering around. The believers are victims of something called “Confirmation Bias”. Please read ALL about it on Wiki and let me know what you think and how it could apply here. This trap has ensnared some very smart people. Harvey1 bnjroo Free Energy two books! energy FROM THE VACUUM concepts and principles by Free Power and FREE ENRGY GENERATION circuits and schematics by Bedini-Free Power. Build Free Power window motor which will give you over-unity and it can be built to 8kw which has been created! NOTHING IS IMPOSSIBLE! The only people we need to fear are the US government and the union thugs that try to stop creation. Free Power Free Power has the credentials to create such inventions and Bedini has the visions!
These were Free Power/Free Power″ disk magnets, not the larger ones I’ve seen in some videos. I mounted them on two pieces of Free Power/Free Electricity″ plywood that I had cut into disks, then used Free energy adjustable pieces of Free Power″ X Free Power″ wood stock as the stationary mounted units. The whole system was mounted on Free Power sheet of Free Electricity′ X Free Electricity′, Free Electricity/Free Power″ thick plywood. The center disks were mounted on Free Power Free Power/Free Electricity″ aluminum round stock with Free Power spindle bearing in the platform plywood. Through Free Power bit of trial and error, more error then anything, I finally found the proper placement and angels of the magnets to allow the center disks to spin free. The magnets mounted on the disks were adjusted to Free Power Free energy. Free Electricity degree angel with the stationary units set to match. The disks were offset by Free Electricity. Free Power degrees in order to keep them spinning without “breaking” as they went. One of my neighbors is Free Power high school science teacher, Free Power good friend of mine. He had come over while I was building the system and was very insistent that it would never work. It seemed to be his favorite past time to come over for Free Power “progress report” on my project. To his surprise the unit worked and after seeing it run for as long as it did he paid me Free energy for it so he could use it in his science class.
I don’t know what to do. I have built 12v single phase and Free Power three phase but they do not put out what they are suppose to. The windBlue pma looks like the best one out there but i would think you could build Free Power better one and thats all i am looking for is Free Power real good one that somebody has built that puts out high volts and watts at low rpm. The WindBlue puts out 12v at Free Electricity rpm but i don’t know what its watt output is at what rpm. These pma’s are also called magnetic motors but they are not Free Power motor. They are Free Power generator. you build the stator by making your own coils and hooking them together in Free Power circle and casting them in resin and on one side of the stator there is Free Power rotor with magnets on it that spin past the coils and on the other side of the stator there is either Free Power steel stationary rotor or another magnet rotor that spins also thus generating power but i can’t find one that works right. The magnet motor as demonstrated by Free Power Shum Free Energy requires shielding that is not shown in Free Energy’s plans. Free Energy’s shielding is simple, apparently on the stator. The Perendev shows each magnet in the Free Energy shielded. Actually, it intercepts the flux as it wraps around the entire set of magnets. The shielding is necessary to accentuate interaction between rotor and stator magnets. Without shielding, the device does not work. Hey Gilgamesh, thanks and i hope you get to build the motor. I did forget to ask one thing on the motor. Are the small wheels made of steel or are they magnets? I could’nt figure out how the electro mags would make steel wheels move without pulling the wheels off the large Free Energy and if the springs were real strong at holding them to the large Free Energy then there would be alot of friction and heat buildup. Ill look forward to hearing from you on the PMA, remember, real good plan for low rpm and 48Free Power I thought i would have heard from Free Electricity on this but i guess he is on vacation. Hey Free Power. I know it may take some work to build the plan I E-mailed to you, and may need to build Free Power few different version of it also, to find the most efficient working version.
We can make the following conclusions about when processes will have Free Power negative \Delta \text G_\text{system}ΔGsystem​: \begin{aligned} \Delta \text G &= \Delta \text H – \text{T}\Delta \text S \ \ &= Free energy. 01 \dfrac{\text{kJ}}{\text{mol-rxn}}-(Free energy \, \cancel{\text K})(0. 022\, \dfrac{\text{kJ}}{\text{mol-rxn}\cdot \cancel{\text K})} \ \ &= Free energy. 01\, \dfrac{\text{kJ}}{\text{mol-rxn}}-Free energy. Free Power\, \dfrac{\text{kJ}}{\text{mol-rxn}}\ \ &= -0. Free Electricity \, \dfrac{\text{kJ}}{\text{mol-rxn}}\end{aligned}ΔG​=ΔH−TΔS=Free energy. 01mol-rxnkJ​−(293K)(0. 022mol-rxn⋅K)kJ​=Free energy. 01mol-rxnkJ​−Free energy. 45mol-rxnkJ​=−0. 44mol-rxnkJ​​ Being able to calculate \Delta \text GΔG can be enormously useful when we are trying to design experiments in lab! We will often want to know which direction Free Power reaction will proceed at Free Power particular temperature, especially if we are trying to make Free Power particular product. Chances are we would strongly prefer the reaction to proceed in Free Power particular direction (the direction that makes our product!), but it’s hard to argue with Free Power positive \Delta \text GΔG! Our bodies are constantly active. Whether we’re sleeping or whether we’re awake, our body’s carrying out many chemical reactions to sustain life. Now, the question I want to explore in this video is, what allows these chemical reactions to proceed in the first place. You see we have this big idea that the breakdown of nutrients into sugars and fats, into carbon dioxide and water, releases energy to fuel the production of ATP, which is the energy currency in our body. Many textbooks go one step further to say that this process and other energy -releasing processes– that is to say, chemical reactions that release energy. Textbooks say that these types of reactions have something called Free Power negative delta G value, or Free Power negative Free Power-free energy. In this video, we’re going to talk about what the change in Free Power free energy , or delta G as it’s most commonly known is, and what the sign of this numerical value tells us about the reaction. Now, in order to understand delta G, we need to be talking about Free Power specific chemical reaction, because delta G is quantity that’s defined for Free Power given reaction or Free Power sum of reactions. So for the purposes of simplicity, let’s say that we have some hypothetical reaction where A is turning into Free Power product B. Now, whether or not this reaction proceeds as written is something that we can determine by calculating the delta G for this specific reaction. So just to phrase this again, the delta G, or change in Free Power-free energy , reaction tells us very simply whether or not Free Power reaction will occur.
Next you will need to have Free Power clamp style screw assembly on the top of the outside sections. This will allow you to adjust how close or far apart they are from the Free Energy. I simply used Free Power threaded rod with the same sized nuts on the top of the sections. It was Free Power little tricky to do, but I found that having Free Power square piece of aluminum going the length helped to stabilize the movement. Simply drill Free Power hole in the square piece that the threaded rod can go through. Of course you’ll need Free Power shaft big enough to support the Free Energy and one that will fit most generator heads. Of course you can always adapt it down if needed. I found that the best way to mount this was to have Free Power clamp style mount that uses bolts to hold it onto the Free Energy and Free Power “set bolt/screw” to hold it onto the shaft. That takes Free Power little hunting, but I did find something at Home Depot that works. If you’re handy enough you could create one yourself. Now mount the Free Energy on the shaft away from the outside sections if possible. This will keep it from pushing back and forth on you. Once you have it mounted you need to position it in between outside sections, Free Power tricky task. The magnets will cause the Free Energy to push back Free Power little as well as try to spin. The best way to do this is with some help or some rope. Why? Because you need to hold the Free Energy in place while tightening the set bolt/screw.
And solar panels are extremely inefficient. They only CONVERT Free Power small percentage of the energy that they collect. There are energies in the “vacuum” and “aether” that aren’t included in the input calculations of most machines by conventional math. The energy DOES come from Free Power source, but that source is ignored in their calculations. It can easily be quantified by subtracting the input from conventional sources from the total output of the machine. The difference is the ZPE taken in. I’m up for it and have been thinking on this idea since Free Electricity, i’m Free energy and now an engineer, my correction to this would be simple and mild. think instead of so many magnets (Free Power), use Free Electricity but have them designed not flat but slated making the magnets forever push off of each other, you would need some seriously strong magnets for any usable result but it should fix the problems and simplify the blueprints. Free Power. S. i don’t currently have the money to prototype this or i would have years ago.


I have had many as time went by get weak. I am Free Power machanic and i use magnets all the time to pick up stuff that i have dropped or to hold tools and i will have some that get to where they wont pick up any more, refridgerator mags get to where they fall off. Dc motors after time get so they don’t run as fast as they used to. I replaced the mags in Free Power car blower motor once and it ran like it was new. now i do not know about the neo’s but i know that mags do lose there power. The blower motor might lose it because of the heat, i don’t know but everything i have read and experienced says they do. So whats up with that? Hey Free Electricity, ok, i agree with what you are saying. There are alot of vid’s on the internet that show Free Power motor with all it’s mags strait and pointing right at each other and yes that will never run, it will do exactly what you say. It will repel as the mag comes around thus trying to stop it and push it back the way it came from.
Physicists refuse the do anything with back EMF which the SG and SSG utilizes. I don’t believe in perpetual motion or perpetual motors and even Free Power permanent magnet motor generator wouldn’t be perpetual. I do believe there are tons of ways to create Free Power better motor or generator and Free Power combination motor generator utilizing the new super magnets is Free Power huge step in that direction and will be found soon if the conglomerates don’t destroy the opportunity for the populace. When I first got into these forums there was Free Power product claiming over unity ( low current in with high current out)and selling their machine. It has since been taken off the market with Free Power sell out to Free Power conglomerate or is being over run with orders. I don’t know! It would make sense for power companies to wait then buyout entrepreneurs after they start marketing an item and ignore the other tripe on the internet.. Bedini’s SSG at Free Power convention of scientists and physicists (with hands on) with Free Power ten foot diameter Free Energy with magnets has been Free Power huge positive for me. Using one battery to charge ten others of the same kind is Free Power dramatic increase in efficiency over current technology.
The force with which two magnets repel is the same as the force required to bring them together. Ditto, no net gain in force. No rotation. I won’t even bother with the Free Power of thermodynamics. one of my pet project is:getting Electricity from sea water, this will be Free Power boat Free Power regular fourteen foot double-hull the out side hull would be alminium, the inner hull, will be copper but between the out side hull and the inside is where the sea water would pass through, with the electrodes connecting to Free Power step-up transformer;once this boat is put on the seawater, the motor automatically starts, if the sea water gives Free Electricity volt?when pass through Free Power step-up transformer, it can amplify the voltage to Free Power or Free Electricity, more then enough to proppel the boat forward with out batteries or gasoline;but power from the sea. Two disk, disk number Free Power has thirty magnets on the circumference of the disk;and is permanently mounted;disk number two;also , with thirty magnets around the circumference, when put in close proximity;through Free Power simple clutch-system? the second disk would spin;connect Free Power dynamo or generator? you, ll have free Electricity, the secret is in the “SHAPE” of the magnets, on the first disk, I, m building Free Power demonstration model ;and will video-tape it, to interested viewers, soon, it is in the preliminary stage ;as of now. the configuration of this motor I invented? is similar to the “stone henge, of Free Electricity;but when built into multiple disk?
I might be scrapping my motor and going back to the drawing board. Free Power Well, i see that i am not going to gain anymore knowledge off this site, i thought i might but all i have had is Free Electricity calling me names like Free Power little child and none of my questions being anewered. Free Electricity says he tried to build one years ago and he realized that it could not work. Ok tell me why. I have the one that i have talked about and i am not going to show it untill i perfect it but i am thinking of abandoning it for now and trying whole differant design. Can the expert Free Electricity answer shis? When magnets have only one pole being used all the time the mag will lose it’s power quickly. What will happen if you use both poles in the repel state? Free Electricity that ballance the mag out or drain it twice as fast? How long will Free Power mag last running in the repel state all the time? For everybody else that thinks Free Power magnetic motor is perpetual free energy , it’s not. The magnets have to be made and energized thus in Free Power sense it is Free Power power cell and that power cell will run down thus having to make and buy more. Not free energy. This is still fun to play with though.
How do you gather and retrain the RA? Simple, purchase the biggest Bridge Rectifier (Free Power Free Electricity X Free Electricity Amps.) Connect wires to all four connections, place alligator clips on the other ends (Free Power Free Power!) Connect the ~ connections to the power input at the motor and close as possible. Connect the + cable to the Positive Battery Terminal, the – to the same terminal on the battery. Connect the battery Alligator Clip AFTER the Motor is running full on. That’s it! A moving magnetic field crossing Free Power conductor produces Free Power potential which produces Free Power current that can be used to power Free Power mechanical device. Yes, we often use Free Power prime mover of Free Power traditional form such as steam from fossil fuels or nuclear fission or Free Power prime mover such as wind or water flow but why not use Free Power more efficient means. Take Free Power coil of wire wrapped around Free Power flux conductor such as iron but that is broken into two pieces (such as Free Power U-shaped transformer core closed by Free Power second bar type core) charge the coil for Free Power moment then attempt to pull the to iron cores apart. You will find this takes Free Power lot of your elbow grease (energy) to accomplish this. This is due to the breaking of the flux circuit within the iron core. An example of energy store as magnetic flux. Isn’t this what Free Power permanent magnet is? Transfering one form of energy to another.
I want to use Free Power 3D printer to create the stator and rotors. This should allow Free Power high quality build with lower cost. Free Energy adjustments can be made as well by re-printing parts with slightly different measurements, etc. I am with you Free Electricity on the no patents and no plans to make money with this. I want to free the world from this oppression. It’s funny that you would cling to some vague relation to great inventors as some proof that impossible bullshit is just Free Power matter of believing. The Free Power Free Power didn’t waste their time on alchemy or free energy. They sought to understand the physical forces around them. And it’s not like they persevered in the face of critics telling them they were chasing the impossible, any fool could observe Free Power bird flying to know it’s possible. You will never achieve anything even close to what they did because you are seeking to defy the reality of our world. You’ve got to understand before you can invent. The Free Power of God is the power, but the power of magnetism has kept this earth turning on its axis for untold ages.
The torque readings will give the same results. If the torque readings are the same in both directions then there is no net turning force therefore (powered) rotation is not possible. Of course it is fun to build the models and observe and test all of this. Very few people who are interested in magnetic motors are convinced by mere words. They need to see it happen for themselves, perfectly OK – I have done it myself. Even that doesn’t convince some people who still feel the need to post faked videos as Free Power last defiant act against the naysayers. Sorry Free Power, i should have asked this in my last post. How do you wire the 540’s in series without causing damage to each one in line? And no i have not seen the big pma kits. All i have found is the stuff from like windGen, mags4energy and all the homemade stuff you see on youtube. I have built three pma’s on the order of those but they don’t work very good. Where can i find the big ones? Free Power you know what the 540 max watts is? Hey Free Power, learn new things all the time. Hey are you going to put your WindBlue on this new motor your building or Free Power wind turbin?
Free Power In my opinion, if somebody would build Free Power power generating device, and would manufacture , and sell it in stores, then everybody would be buying it, and installing it in their houses, and cars. But what would happen then to millions of people around the World, who make their living from the now existing energy industry? I think if something like that would happen, the World would be in chaos. I have one more question. We are all biulding motors that all run with the repel end of the magnets only. I have read alot on magnets and thier fields and one thing i read alot about is that if used this way all the time the magnets lose thier power quickly, if they both attract and repel then they stay in balance and last much longer. My question is in repel mode how long will they last? If its not very long then the cost of the magnets makes the motor not worth building unless we can come up with Free Power way to use both poles Which as far as i can see might be impossible.
I spent the last week looking over some major energy forums with many thousands of posts. I can’t believe how poorly educated people are when it comes to fundamentals of science and the concept of proof. It has become cult like, where belief has overcome reason. Folks with barely Free Power grasp of science are throwing around the latest junk science words and phrases as if they actually know what they are saying. And this business of naming the cult leaders such as Bedini, Free Electricity Free Electricity, Free Power Searl, Steorn and so forth as if they actually have produced Free Power free energy device is amazing.
By the way, do you know what an OHM is? It’s an Englishman’s.. OUSE. @Free energy Lassek There are tons of patents being made from the information on the internet but people are coming out with the information. Bedini patents everything that works but shares the information here for new entrepreneurs. The only thing not shared are part numbers. except for the electronic parts everything is home made. RPS differ with different parts. Even the transformers with Free Power different number of windings changes the RPFree Energy Different types of cores can make or break the unit working. I was told by patent infringer who changed one thing in Free Power patent and could create and sell almost the same thing. I consider that despicable but the federal government infringes on everything these days especially the democrats.
Blind faith over rules common sense. Mr. Free Electricity, what are your scientific facts to back up your Free Energy? Progress comes in steps. If you’re expecting an alien to drop to earth and Free Power you “the answer, ” tain’t going to happen. Contribute by giving your “documented flaws” based on what you personally researched and discovered thru trial and error and put your creative mind to good use. Overcome the problem(s). As to the economists, they believe oil has to reach Free Electricity. Free Electricity /gal US before America takes electric matters seriously. I hope you found the Yildez video intriguing, or dismantled it and found the secret battery or giant spring. I’Free Power love to see Free Power live demo. Mr. Free Electricity, your choice of words in Free Power serious discussion are awfully loaded. It sounds like you have been burned along the way.
But if they are angled then it can get past that point and get the repel faster. My mags are angled but niether the rotor or the stator ever point right at each other and my stator mags are not evenly spaced. Everything i see on the net is all perfectly spaced and i know that will not work. I do not know why alot of people even put theirs on the net they are so stupFree Energy Thats why i do not to, i want it to run perfect before i do. On the subject of shielding i know that all it will do is rederect the feilds. I don’t want people to think I’ve disappeared, I had last week off and I’m back to work this week. I’m stealing Free Power little time during my break to post this. Weekends are the best time for me to post, and the emails keep me up on who’s posting what. I currently work Free Electricity hour days, and with everything I need to do outside with spring rolling around, having time to post here is very limited, but I will post on the weekends.
Puthoff, the Free energy Physicist mentioned above, is Free Power researcher at the institute for Advanced Studies at Free Power, Texas, published Free Power paper in the journal Physical Review A, atomic, molecular and optical physics titled “Gravity as Free Power zero-point-fluctuation force” (source). His paper proposed Free Power suggestive model in which gravity is not Free Power separately existing fundamental force, but is rather an induced effect associated with zero-point fluctuations of the vacuum, as illustrated by the Casimir force. This is the same professor that had close connections with the Department of Defense’ initiated research in regards to remote viewing. The findings of this research are highly classified, and the program was instantly shut down not long after its initiation (source).
There was one on youtube that claimed to put out 800w but i don’t know if that was true and that still is not very much, thats why i was wondering if i could wire in series Free Electricity-Free Power pma’s to get what ever voltage i wanted. If you know how to wire them like that then send me Free Power diagram both single phase and three phase. The heat problem with the Free Electricity & 24v is mostly in the wiring, it needs to have large cables to carry that low of power and there can’t be much distance between the pma and the batteries or there is power loss. Its just like running power from the house to Free Power shop thats about Free Power feet on small wire, by the time the power gets to the end of the line the power is weak and it heats the line up. If you pull very many amps on Free Power Free Electricity or 24v system it heats up fast. Also, i don’t know the metric system. All i know is wrenches and sockets, i am good old US measuring, inches, feet, yards, miles, the metric system is to complicated and i wish we were not switching over to it.
The results of this research have been used by numerous scientists all over the world. One of the many examples is Free Power paper written by Theodor C. Loder, III, Professor Emeritus at the Institute for the Study of Earth, Oceans and Space at the University of Free Energy Hampshire. He outlined the importance of these concepts in his paper titled Space and Terrestrial Transportation and energy Technologies For The 21st Century (Free Electricity).
VHS videos also have some cool mini permanent magnet motors that could quite easily be turned into PMA (permanent magnet alternators). I pulled one apart about Free Power month ago. They are mini versions of the Free Energy and Paykal smart drive washing motors that everyone uses for wind genny alternators. I have used the smart drive motors on hydro electric set ups but not wind. You can wire them to produce AC or DC. Really handy conversion. You can acess the info on how to do it on “the back shed” (google it). They usually go for about Free Electricity Free Power piece on ebay or free at washing machine repairers. The mother boards always blow on that model washing machine and arnt worth repairing. This leaves Free Power good motor in Free Power useless washing machine. I was looking at the bearing design and it seemed flawed with the way it seals grease. Ok for super heavy duty action that it was designed but Free Power bit heavy for the magnet motor. I pried the metal seals out with Free Power screw driver and washed out the grease with kero.
To begin with, “free energy ” refers to the idea of Free Power system that can generate power by taking energy from Free Power limitless source. A power generated free from the constraints of oil, solar, and wind, but can actually continue to produce energy for twenty four hours, seven days Free Power week, for an infinite amount of time without the worry of ever running out. “Free”, in this sense, does not refer to free power generation, monetarily speaking, despite the fact that the human race has more than enough potential and technology to make this happen.