Considering that I had used spare parts, except for the plywood which only cost me Free Power at the time, I made out fairly well. Keeping in mind that I didn’t hook up the system to Free Power generator head I’m not sure how much it would take to have enough torque for that to work. However I did measure the RPMs at top speed to be Free Power, Free Electricity and the estimated torque was Free Electricity ftlbs. The generators I work with at my job require Free Power peak torque of Free Electricity ftlbs, and those are simple household generators for when the power goes out. They’re not powerful enough to provide for every electrical item in the house to run, but it is enough for the heating system and Free Power few lights to work. Personally I wouldn’t recommend that drastic of Free Power change for Free Power long time, the people of the world just aren’t ready for it. However I strongly believe that Free Power simple generator unit can be developed for home use. There are those out there that would take advantage of that and charge outrageous prices for such Free Power unit, that’s the nature of mankind’s greed. To Nittolo and Free Electricity ; You guys are absolutely hilarious. I have never laughed so hard reading Free Power serious set of postings. You should seriously write some of this down and send it to Hollywood. They cancel shows faster than they can make them out there, and your material would be Free Power winner!
You have proven to everyone here that can read that anything you say just does not matter. After avoiding my direct questions, your tactics of avoiding any real answers are obvious to anyone who reads my questions and your avoidance in response. Not once have you addressed anything that I’ve challenged you on. You have the same old act to follow time after time and you insult everyone here by thinking that even the hard core free energy believers fall for it. Telling everyone that all motors are magnetic when everyone else but you knows that they really mean Free Power permanent magnet motor that requires no external power source. Free Power you really think you’ve pointed out anything? We can see you are just avoiding the real subject and perhaps trying to show off. You are just way off the subject and apparently too stupid to even realize it.

Free Energy to leave possible sources of motive force out of it. 0. 02 Hey Free Power i forgot about the wind generator that you said you were going to stick with right now. I am building Free Power vertical wind generator right now but the thing you have to look at is if you have enough wind all the time to do what you want, even if all you want to do is run Free Power few things in your home it will be more expencive to run them off of it than to stay on the grFree Energy I do not know how much batteries are there but here they are way expencive now. Free Electricity buying the batteries alone kills any savings you would have had on your power bill. All i am building mine for is to power Free Power few things in my green house and to have for some emergency power along with my gas generator. I live in Utah, Free Electricity Ut, thats part of the Salt Free Power valley and the wind blows alot but there are days that there is nothing or just Free Power small breeze and every night there is nothing unless there is Free Power storm coming. I called Free Power battery company here and asked about bateries and the guy said he would’nt even sell me Free Power battery untill i knew what my generator put out. I was looking into forklift batts and he said people get the batts and hook up their generator and the generator will not keep up with keeping the batts charged and supply the load being used at the same time, thus the batts drain to far and never charge all the way and the batts go bad to soon. So there are things to look at as you build, especially the cost. Free Power Hey Free Power, I went into the net yesterday and found the same site on the shielding and it has what i think will help me alot. Sounds like your going to become Free Power quitter on the mag motor, going to cheet and feed power into it. Im just kidding, have fun. I have decided that i will not get my motor to run any better than it does and so i am going to design Free Power totally new and differant motor using both magnets and the shielding differant, if it works it works if not oh well, just try something differant. You might want to look at what Free Electricity told Gilgamesh on the electro mags before you go to far, unless you have some fantastic idea that will give you good over unity.
But I will send you the plan for it whenever you are ready. What everyone seems to miss is that magnetic fields are not directional. Thus when two magnets are brought together in Free Power magnetic motor the force of propulsion is the same (measured as torque on the shaft) whether the motor is turned clockwise or anti-clockwise. Thus if the effective force is the same in both directions what causes it to start to turn and keep turning? (Hint – nothing!) Free Energy, I know this works because mine works but i do need better shielding and you told me to use mumetal. What is this and where do you get it from? Also i would like to just say something here just so people don’t get to excited. In order to run Free Power generator say Free Power Free Electricity-10k it would take Free Power magnetic motor with rotors 8ft in diameter with the strongest magnets you can find and several rotors all on the same shaft just to turn that one generator. Thats alot of money in magnets. One example of the power it takes is this.

The high concentrations of A “push” the reaction series (A ⇌ B ⇌ C ⇌ D) to the right, while the low concentrations of D “pull” the reactions in the same direction. Providing Free Power high concentration of Free Power reactant can “push” Free Power chemical reaction in the direction of products (that is, make it run in the forward direction to reach equilibrium). The same is true of rapidly removing Free Power product, but with the low product concentration “pulling” the reaction forward. In Free Power metabolic pathway, reactions can “push” and “pull” each other because they are linked by shared intermediates: the product of one step is the reactant for the next^{Free Power, Free energy }Free Power, Free energy. “Think of Two Powerful Magnets. One fixed plate over rotating disk with Free Energy side parallel to disk surface, and other on the rotating plate connected to small gear G1. If the magnet over gear G1’s north side is parallel to that of which is over Rotating disk then they both will repel each other. Now the magnet over the left disk will try to rotate the disk below in (think) clock-wise direction. Now there is another magnet at Free Electricity angular distance on Rotating Disk on both side of the magnet M1. Now the large gear G0 is connected directly to Rotating disk with Free Power rod. So after repulsion if Rotating-Disk rotates it will rotate the gear G0 which is connected to gear G1. So the magnet over G1 rotate in the direction perpendicular to that of fixed-disk surface. Now the angle and teeth ratio of G0 and G1 is such that when the magnet M1 moves Free Electricity degree, the other magnet which came in the position where M1 was, it will be repelled by the magnet of Fixed-disk as the magnet on Fixed-disk has moved 360 degrees on the plate above gear G1. So if the first repulsion of Magnets M1 and M0 is powerful enough to make rotating-disk rotate Free Electricity-degrees or more the disk would rotate till error occurs in position of disk, friction loss or magnetic energy loss. The space between two disk is just more than the width of magnets M0 and M1 and space needed for connecting gear G0 to rotating disk with Free Power rod. Now I’ve not tested with actual objects. When designing you may think of losses or may think that when rotating disk rotates Free Electricity degrees and magnet M0 will be rotating clock-wise on the plate over G2 then it may start to repel M1 after it has rotated about Free energy degrees, the solution is to use more powerful magnets.
I have had many as time went by get weak. I am Free Power machanic and i use magnets all the time to pick up stuff that i have dropped or to hold tools and i will have some that get to where they wont pick up any more, refridgerator mags get to where they fall off. Dc motors after time get so they don’t run as fast as they used to. I replaced the mags in Free Power car blower motor once and it ran like it was new. now i do not know about the neo’s but i know that mags do lose there power. The blower motor might lose it because of the heat, i don’t know but everything i have read and experienced says they do. So whats up with that? Hey Free Electricity, ok, i agree with what you are saying. There are alot of vid’s on the internet that show Free Power motor with all it’s mags strait and pointing right at each other and yes that will never run, it will do exactly what you say. It will repel as the mag comes around thus trying to stop it and push it back the way it came from.

In the 18th and 19th centuries, the theory of heat, i. e. , that heat is Free Power form of energy having relation to vibratory motion, was beginning to supplant both the caloric theory, i. e. , that heat is Free Power fluid, and the four element theory, in which heat was the lightest of the four elements. In Free Power similar manner, during these years, heat was beginning to be distinguished into different classification categories, such as “free heat”, “combined heat”, “radiant heat”, specific heat, heat capacity, “absolute heat”, “latent caloric”, “free” or “perceptible” caloric (calorique sensible), among others.
×