The inventor of the Perendev magnetic motor (Free Electricity Free Electricity) is now in jail for defrauding investors out of more than Free Power million dollars because he never delivered on his promised motors. Of course he will come up with some excuse, or his supporters will that they could have delivered if they hade more time – or the old classsic – the plans were lost in Free Power Free Electricity or stolen. The sooner we jail all free energy motor con artists the better for all, they are Free Power distraction and they prey on the ignorant. To create Free Power water molecule X energy was released. Thermodynamic laws tell us that X+Y will be required to separate the molecule. Thus, it would take more energy to separate the water molecule (in whatever form) then the reaction would produce. The reverse however (separating the bond using Free Power then recombining for use) would be Free Power great implementation. But that is the bases on the hydrogen fuel cell. Someone already has that one. Instead of killing our selves with the magnetic “theory”…has anyone though about water-fueled engines?.. much more simple and doable …an internal combustion engine fueled with water.. well, not precisely water in liquid state…hydrogen and oxygen mixed…in liquid water those elements are chained with energy …energy that we didn’t spend any effort to “create”.. (nature did the job for us).. and its contained in the molecular union.. so the prob is to decompose the liquid water into those elements using small amounts of energy (i think radio waves could do the job), and burn those elements in Free Power effective engine…can this be done or what?…any guru can help?… Magnets are not the source of the energy.
Next you will need to have Free Power clamp style screw assembly on the top of the outside sections. This will allow you to adjust how close or far apart they are from the Free Energy. I simply used Free Power threaded rod with the same sized nuts on the top of the sections. It was Free Power little tricky to do, but I found that having Free Power square piece of aluminum going the length helped to stabilize the movement. Simply drill Free Power hole in the square piece that the threaded rod can go through. Of course you’ll need Free Power shaft big enough to support the Free Energy and one that will fit most generator heads. Of course you can always adapt it down if needed. I found that the best way to mount this was to have Free Power clamp style mount that uses bolts to hold it onto the Free Energy and Free Power “set bolt/screw” to hold it onto the shaft. That takes Free Power little hunting, but I did find something at Home Depot that works. If you’re handy enough you could create one yourself. Now mount the Free Energy on the shaft away from the outside sections if possible. This will keep it from pushing back and forth on you. Once you have it mounted you need to position it in between outside sections, Free Power tricky task. The magnets will cause the Free Energy to push back Free Power little as well as try to spin. The best way to do this is with some help or some rope. Why? Because you need to hold the Free Energy in place while tightening the set bolt/screw.
This is EXACTLY spot on. The reason free magnet motors will never work is because people are confusing energy with force. Yes, magnets in principle have an inherent force and can act on one another. But you cannot throw Free Power few magnets in Free Power closed system and have their force attract and repel each other to generate free motion because Free Power magnetic field has equal sides attraction and repulsion and any motion with the magnets that appears to utilize one would cancel out the other. The sum of energy needed to keep Free Power system with permanent magnets in motion is going to always be greater than, even by Free Power hairline in Free Power perfectly designed system, than any energy that can be extracted even if that energy is only used just for keeping them in some form of rotational inertia. @Free Energy Lets do this Free Energy.
The Free Power free energy is given by G = H − TS, where H is the enthalpy, T is the absolute temperature, and S is the entropy. H = U + pV, where U is the internal energy , p is the pressure, and Free Power is the volume. G is the most useful for processes involving Free Power system at constant pressure p and temperature T, because, in addition to subsuming any entropy change due merely to heat, Free Power change in G also excludes the p dV work needed to “make space for additional molecules” produced by various processes. Free Power free energy change therefore equals work not associated with system expansion or compression, at constant temperature and pressure. (Hence its utility to solution-phase chemists, including biochemists.)
×