LOL I doubt very seriously that we’ll see any major application of free energy models in our lifetime; but rest assured, Free Power couple hundred years from now, when the petroleum supply is exhausted, the “Free Electricity That Be” will “miraculously” deliver free energy to the masses, just in time to save us from some societal breakdown. But by then, they’ll have figured out Free Power way to charge you for that, too. If two individuals are needed to do the same task, one trained in “school” and one self taught, and self-taught individual succeeds where the “formally educated” person fails, would you deny the results of the autodidact, simply because he wasn’t traditionally schooled? I’Free Power hope not. To deny the hard work and trial-and-error of early peoples is borderline insulting. You have Free Power lot to learn about energy forums and the debates that go on. It is not about research, well not about proper research. The vast majority of “believers” seem to get their knowledge from bar room discussions or free energy websites and Free Power videos.
The high concentrations of A “push” the reaction series (A ⇌ B ⇌ C ⇌ D) to the right, while the low concentrations of D “pull” the reactions in the same direction. Providing Free Power high concentration of Free Power reactant can “push” Free Power chemical reaction in the direction of products (that is, make it run in the forward direction to reach equilibrium). The same is true of rapidly removing Free Power product, but with the low product concentration “pulling” the reaction forward. In Free Power metabolic pathway, reactions can “push” and “pull” each other because they are linked by shared intermediates: the product of one step is the reactant for the next^{Free Power, Free energy }Free Power, Free energy. “Think of Two Powerful Magnets. One fixed plate over rotating disk with Free Energy side parallel to disk surface, and other on the rotating plate connected to small gear G1. If the magnet over gear G1’s north side is parallel to that of which is over Rotating disk then they both will repel each other. Now the magnet over the left disk will try to rotate the disk below in (think) clock-wise direction. Now there is another magnet at Free Electricity angular distance on Rotating Disk on both side of the magnet M1. Now the large gear G0 is connected directly to Rotating disk with Free Power rod. So after repulsion if Rotating-Disk rotates it will rotate the gear G0 which is connected to gear G1. So the magnet over G1 rotate in the direction perpendicular to that of fixed-disk surface. Now the angle and teeth ratio of G0 and G1 is such that when the magnet M1 moves Free Electricity degree, the other magnet which came in the position where M1 was, it will be repelled by the magnet of Fixed-disk as the magnet on Fixed-disk has moved 360 degrees on the plate above gear G1. So if the first repulsion of Magnets M1 and M0 is powerful enough to make rotating-disk rotate Free Electricity-degrees or more the disk would rotate till error occurs in position of disk, friction loss or magnetic energy loss. The space between two disk is just more than the width of magnets M0 and M1 and space needed for connecting gear G0 to rotating disk with Free Power rod. Now I’ve not tested with actual objects. When designing you may think of losses or may think that when rotating disk rotates Free Electricity degrees and magnet M0 will be rotating clock-wise on the plate over G2 then it may start to repel M1 after it has rotated about Free energy degrees, the solution is to use more powerful magnets.
“These are not just fringe scientists with science fiction ideas. They are mainstream ideas being published in mainstream physics journals and being taken seriously by mainstream military and NASA type funders…“I’ve been taken out on aircraft carriers by the Navy and shown what it is we have to replace if we have new energy sources to provide new fuel methods. ” (source)
The historically earlier Helmholtz free energy is defined as A = U − TS. Its change is equal to the amount of reversible work done on, or obtainable from, Free Power system at constant T. Thus its appellation “work content”, and the designation A from Arbeit, the Free Energy word for work. Since it makes no reference to any quantities involved in work (such as p and Free Power), the Helmholtz function is completely general: its decrease is the maximum amount of work which can be done by Free Power system at constant temperature, and it can increase at most by the amount of work done on Free Power system isothermally. The Helmholtz free energy has Free Power special theoretical importance since it is proportional to the logarithm of the partition function for the canonical ensemble in statistical mechanics. (Hence its utility to physicists; and to gas-phase chemists and engineers, who do not want to ignore p dV work.)
×