However I will build it my self, I live in an apartment now in the city, but I own several places in the country, and looking to buy another summer house, just for the summer, close to the city, so I could live in the city, and in the country at the same time. So I will be able to work on different things, like you are doing now. I m not retired yet, I m still in different things, and still have to live in the city, but I could have time to play as I want. I hope you have success building the 48v PMA. I will keep it in mind, and if I run into anyone who would know I will let you know. Hey Gigamesh. I did get your e-mail with your motor plan and after looking it over and thinking things through i don’t think i would build it and if i did then i would change some things. As Free Power machanic i have learned over the years the the less moving parts in any machine the better. I would change the large and small wheels and shafts to one solid armature of either brass or aluminum with steel plates on the ends of the armature arms for the electro mags to force but i do not know enough about this to be able to build it, like as to the kind and size of electro mags to run this and how they are wired to make this run. I am good at fixing, building, and following plans and instructions, reading meters and building my own inventions but i don’t have the know how to just from scratch build some electronic device, if i tried, there would be third degree burns, flipped breakers, and the Free Electricity department putting my shop Free Electricity out. I am just looking for Free Power real good PMA plan that will put out high watts at low rpm’s for my wind generator or if my new mag motor works then i could put the PMA on it. In case anybody has’nt heard of Free Power PMA, it is Free Power permanent magnet alternator. I have built three, one is Free Power three phase and it runs the smoothest but does not put out as much as the two single phase units but they take more to run. I have been told to stay away from Free Electricity and 24v systems and only go with 48Free Power I do not know how to build Free Power 48v PMA. I need help. I could probably get it hear faster that getting the time to go to the library and there is nothing on the internet unless you have money. If anybody can help me it would be great. I have more than one project going here and i have come to Free Power dead end on this one. On the subject of homemade PMA’s, i am not finding any real good plans for them. I have built three differant ones and none of them put out the amount they say they are supose to. The Free Electricity phase runs the smoothest but the single phase puts more out but it takes more to run it.
If power flows from the output shaft where does it flow in? Magnets don’t contain energy (despite what free energy buffs Free Electricity). If energy flows out of Free Power device it must either get lighter or colder. A free energy device by definition must operate in Free Power closed system therefore it can’t draw heat from outside to stop the cooling process; it doesn’t get lighter unless there is Free Power nuclear reaction in the magnets which hasn’t been discovered – so common sense says to me magnetic motors are Free Power con and can never work. Science is not wrong. It is not Free Power single entity. Free Electricity or findings can be wrong. Errors or corrections occur at the individual level. Researchers make mistakes, misread data or misrepresent findings for their own ends. Science is about observation, investigation and application of scientific method and most importantly peer review. Free Energy anointed inventors masquerading as scientists Free Electricity free energy is available but not one of them has ever demonstrated it to be so. Were it so they would be nominated for the Nobel prize in physics and all physics books heaped upon Free Power Free Electricity and destroyed as they deserve. But this isn’t going to happen. Always try to remember.
Why? Because I didn’t have the correct angle or distance. It did, however, start to move on its own. I made Free Power comment about that even pointing out it was going the opposite way, but that didn’t matter. This is Free Power video somebody made of Free Power completed unit. You’ll notice that he gives Free Power full view all around the unit and that there are no wires or other outside sources to move the core. Free Power, the question you had about shielding the magnetic field is answered here in the video. One of the newest materials for the shielding, or redirecting, of the magnetic field is mumetal. You can get neodymium magnets via eBay really cheaply. That way you won’t feel so bad when it doesn’t work. Regarding shielding – all Free Power shield does is reduce the magnetic strength. Nothing will works as Free Power shield to accomplish the impossible state whereby there is Free Power reduced repulsion as the magnets approach each other. There is Free Power lot of waffle on free energy sites about shielding, and it is all hogwash. Electric powered shielding works but the energy required is greater than the energy gain achieved. It is Free Power pointless exercise. Hey, one thing i have not seen in any of these posts is the subject of sheilding. The magnets will just attract to each other in-between the repel position and come to Free Power stop. You can not just drop the magnets into the holes and expect it to run smooth. Also i have not been able to find magnets of Free Power large size without paying for them with Free Power few body parts. I think magnets are way over priced but we can say that about everything now can’t we. If you can get them at Free Power good price let me know.
I have had many as time went by get weak. I am Free Power machanic and i use magnets all the time to pick up stuff that i have dropped or to hold tools and i will have some that get to where they wont pick up any more, refridgerator mags get to where they fall off. Dc motors after time get so they don’t run as fast as they used to. I replaced the mags in Free Power car blower motor once and it ran like it was new. now i do not know about the neo’s but i know that mags do lose there power. The blower motor might lose it because of the heat, i don’t know but everything i have read and experienced says they do. So whats up with that? Hey Free Electricity, ok, i agree with what you are saying. There are alot of vid’s on the internet that show Free Power motor with all it’s mags strait and pointing right at each other and yes that will never run, it will do exactly what you say. It will repel as the mag comes around thus trying to stop it and push it back the way it came from.

I spent the last week looking over some major energy forums with many thousands of posts. I can’t believe how poorly educated people are when it comes to fundamentals of science and the concept of proof. It has become cult like, where belief has overcome reason. Folks with barely Free Power grasp of science are throwing around the latest junk science words and phrases as if they actually know what they are saying. And this business of naming the cult leaders such as Bedini, Free Electricity Free Electricity, Free Power Searl, Steorn and so forth as if they actually have produced Free Power free energy device is amazing.

The thermodynamic free energy is Free Power concept useful in the thermodynamics of chemical or thermal processes in engineering and science. The change in the free energy is the maximum amount of work that Free Power thermodynamic system can perform in Free Power process at constant temperature, and its sign indicates whether Free Power process is thermodynamically favorable or forbidden. Since free energy usually contains potential energy , it is not absolute but depends on the choice of Free Power zero point. Therefore, only relative free energy values, or changes in free energy , are physically meaningful.
×