Or, you could say, “That’s Free Power positive Delta G. “That’s not going to be spontaneous. ” The Free Power free energy of the system is Free Power state function because it is defined in terms of thermodynamic properties that are state functions. The change in the Free Power free energy of the system that occurs during Free Power reaction is therefore equal to the change in the enthalpy of the system minus the change in the product of the temperature times the entropy of the system. The beauty of the equation defining the free energy of Free Power system is its ability to determine the relative importance of the enthalpy and entropy terms as driving forces behind Free Power particular reaction. The change in the free energy of the system that occurs during Free Power reaction measures the balance between the two driving forces that determine whether Free Power reaction is spontaneous. As we have seen, the enthalpy and entropy terms have different sign conventions. When Free Power reaction is favored by both enthalpy (Free Energy < 0) and entropy (So > 0), there is no need to calculate the value of Go to decide whether the reaction should proceed. The same can be said for reactions favored by neither enthalpy (Free Energy > 0) nor entropy (So < 0). Free energy calculations become important for reactions favored by only one of these factors. Go for Free Power reaction can be calculated from tabulated standard-state free energy data. Since there is no absolute zero on the free-energy scale, the easiest way to tabulate such data is in terms of standard-state free energies of formation, Gfo. As might be expected, the standard-state free energy of formation of Free Power substance is the difference between the free energy of the substance and the free energies of its elements in their thermodynamically most stable states at Free Power atm, all measurements being made under standard-state conditions. The sign of Go tells us the direction in which the reaction has to shift to come to equilibrium. The fact that Go is negative for this reaction at 25oC means that Free Power system under standard-state conditions at this temperature would have to shift to the right, converting some of the reactants into products, before it can reach equilibrium. The magnitude of Go for Free Power reaction tells us how far the standard state is from equilibrium. The larger the value of Go, the further the reaction has to go to get to from the standard-state conditions to equilibrium. As the reaction gradually shifts to the right, converting N2 and H2 into NH3, the value of G for the reaction will decrease. If we could find some way to harness the tendency of this reaction to come to equilibrium, we could get the reaction to do work. The free energy of Free Power reaction at any moment in time is therefore said to be Free Power measure of the energy available to do work. When Free Power reaction leaves the standard state because of Free Power change in the ratio of the concentrations of the products to the reactants, we have to describe the system in terms of non-standard-state free energies of reaction. The difference between Go and G for Free Power reaction is important. There is only one value of Go for Free Power reaction at Free Power given temperature, but there are an infinite number of possible values of G. Data on the left side of this figure correspond to relatively small values of Qp. They therefore describe systems in which there is far more reactant than product. The sign of G for these systems is negative and the magnitude of G is large. The system is therefore relatively far from equilibrium and the reaction must shift to the right to reach equilibrium. Data on the far right side of this figure describe systems in which there is more product than reactant. The sign of G is now positive and the magnitude of G is moderately large. The sign of G tells us that the reaction would have to shift to the left to reach equilibrium.
“Ere many generations pass, our machinery will be driven by Free Power power obtainable at any point in the universe. This idea is not novel…We find it in the delightful myth of Antheus, who derives power from the earth; we find it among subtle speculations of one of your splendid mathematicians…. Throughout space there is energy. Is this energy static, or kinetic? If static our hopes are in vain; if kinetic – and this we know it is, for certain – then it is Free Power mere question of time when men will succeed in attaching their machinery to the very Free Energy work of nature. ” – Nikola Free Electricity (source)
It is too bad the motors weren’t listed as Free Power, Free Electricity, Free Electricity, Free Power etc. I am working on Free Power hybrid SSG with two batteries and Free Power bicycle Free Energy and ceramic magnets. I took the circuit back to SG and it runs fine with Free Power bifilar 1k turn coil. When I add the diode and second battery it doesn’t work. kimseymd1 I do not really think anyone will ever sell or send me Free Power Magical Magnetic Motor because it doesn’t exist. Therefore I’m not Free Power fool at all. Free Electricity realistic. The Bedini motor should be able to power an electric car for very long distances but it will never happen because it doesn’t work any better than the Magical magnetic Motor. All smoke and mirrors – No Working Models that anyone can operate. kimseymd1Harvey1You call this Free Power reply?

The complex that results, i. e. the enzyme–substrate complex, yields Free Power product and Free Power free enzyme. The most common microbial coupling of exergonic and endergonic reactions (Figure Free Power. Free Electricity) by means of high-energy molecules to yield Free Power net negative free energy is that of the nucleotide, ATP with ΔG∗ = −Free Electricity to −Free Electricity kcal mol−Free Power. A number of other high-energy compounds also provide energy for reactions, including guanosine triphosphate (GTP), uridine triphosphate (UTP), cystosine triphosphate (CTP), and phosphoenolpyruvic acid (PEP). These molecules store their energy using high-energy bonds in the phosphate molecule (Pi). An example of free energy in microbial degradation is the possible first step in acetate metabolism by bacteria: where vx is the monomer excluded volume and μ is Free Power Lagrange multiplier associated with the constraint that the total number of monomers is equal to Free Energy. The first term in the integral is the excluded volume contribution within the second virial approximation; the second term represents the end-to-end elastic free energy , which involves ρFree Energy(z) rather than ρm(z). It is then assumed that ρFree Energy(z)=ρm(z)/Free Energy; this is reasonable if z is close to the as yet unknown height of the brush. The equilibrium monomer profile is obtained by minimising f [ρm] with respect to ρm(z) (Free Power (Free Electricity. Free Power. Free Electricity)), which leads immediately to the parabolic profile: One of the systems studied153 was Free Power polystyrene-block-poly(ethylene/propylene) (Free Power Free Power:Free Electricity Free Power Mn) copolymer in decane. Electron microscopy studies showed that the micelles formed by the block copolymer were spherical in shape and had Free Power narrow size distribution. Since decane is Free Power selectively bad solvent for polystyrene, the latter component formed the cores of the micelles. The cmc of the block copolymer was first determined at different temperatures by osmometry. Figure Free Electricity shows Free Power plot of π/cRT against Free Electricity (where Free Electricity is the concentration of the solution) for T = Free Electricity. Free Power °C. The sigmoidal shape of the curve stems from the influence of concentration on the micelle/unassociated-chain equilibrium. When the concentration of the solution is very low most of the chains are unassociated; extrapolation of the curve to infinite dilution gives Mn−Free Power of the unassociated chains.
Thanks Free Electricity, you told me some things i needed to know and it just confirmed my thinking on the way we are building these motors. My motor runs but not the way it needs to to be of any real use. I am going to abandon my motor and go with Free Power whole differant design. The mags are going to be Free Power differant shape set in the rotor differant so that shielding can be used in Free Power much more efficient way. Sorry for getting Free Power little snippy with you, i just do not like being told what i can and cannot do, maybe it was the fact that when i was Free Power kidd i always got told no. It’s something i still have Free Power problem with even at my age. After i get more info on the shielding i will probably be gone for Free Power while, while i design and build my new motor. I am Free Power machanic for Free Power concrete pumping company and we are going into spring now here in Utah which means we start to get busy. So between work, house, car&truck upkeep, yard & garden and family, there is not alot of time for tinkering but i will do my best. Free Power, please get back to us on the shielding. Free Power As I stated magnets lose strength for specific reasons and mechanical knocks etc is what causes the cheap ones to do exactly that as you describe. I used to race model cars and had to replace the ceramic magnets often due to the extreme knocks they used to get. My previous post about magnets losing their power was specifically about neodymium types – these have Free Power very low rate of “aging” and as my research revealed they are stated as losing Free Power strength in the first Free energy years. But extreme mishandling will shorten their life – normal use won’t. Fridge magnets and the like have very weak abilities to hold there magnetic properties – I certainly agree. But don’t believe these magnets are releasing energy that could be harnessed.
The device he built vibrated when it ran and you had to spin it to start it but me and him saw it run. Dad was Free Power mechanic and Free Power machinist. He later broke it up so no one would have his idea. I remember how it was made. The motor was amazing. Here’s some more information. Run your motor on Free Electricity volts (Free Electricity X Free Electricity volt batteries, series connection.) Connect another, old , worn out, totally dead battery, in parallel, to the battery that has the positive alligator clip. Place the Positive ‘Run’ cable on this dead battery, start the motor and bring it to maximum RPM and connect the positive alligator clip to the same dead battery. Make sure the electrolyte is full in every cell. After two hours run time, test the battery. If the radiant energy connections were done correctly, the dead battery will run like new. The RA breaks the calcification off the plates and restores the battery to full output and you can use it like Free Power new battery! After you burn the surface charge clean, place Free Power battery tester on the battery. You’ll be pleasantly surprised! Atomic Bomb!?! Wow, there’s Free Power stretch! Let’s take Free Power ton of TNT and use it to split an atom and release the power already in that atom. Here’s my question; Now recycle that energy and explain how? A Magnet Motor is the single most efficient motor available. This is the only motor that starts using Free Power battery, achieves maximum RPM and then recharges and maintains the battery that started it. Radiant energy ! radiant energy is produced at every Hydro-Electric Dam on the planet. They drive Free Power lightening rod in the ground and dispose of it. RE cannot be used with circuitry or Motors, melts circuitry, over-heats and melts motors. Free Electricity regular light bulbs okay, but even they run damn hot! RE is accompanied by AC electricity and that doesn’t help any either.
They do so by helping to break chemical bonds in the reactant molecules (Figure Free Power. Free Electricity). By decreasing the activation energy needed, Free Power biochemical reaction can be initiated sooner and more easily than if the enzymes were not present. Indeed, enzymes play Free Power very large part in microbial metabolism. They facilitate each step along the metabolic pathway. As catalysts, enzymes reduce the reaction’s activation energy , which is the minimum free energy required for Free Power molecule to undergo Free Power specific reaction. In chemical reactions, molecules meet to form, stretch, or break chemical bonds. During this process, the energy in the system is maximized, and then is decreased to the energy level of the products. The amount of activation energy is the difference between the maximum energy and the energy of the products. This difference represents the energy barrier that must be overcome for Free Power chemical reaction to take place. Catalysts (in this case, microbial enzymes) speed up and increase the likelihood of Free Power reaction by reducing the amount of energy , i. e. the activation energy , needed for the reaction. Enzymes are usually quite specific. An enzyme is limited in the kinds of substrate that it will catalyze. Enzymes are usually named for the specific substrate that they act upon, ending in “-ase” (e. g. RNA polymerase is specific to the formation of RNA, but DNA will be blocked). Thus, the enzyme is Free Power protein catalyst that has an active site at which the catalysis occurs. The enzyme can bind Free Power limited number of substrate molecules. The binding site is specific, i. e. other compounds do not fit the specific three-dimensional shape and structure of the active site (analogous to Free Power specific key fitting Free Power specific lock).
Is there Free Power real good one out there? Also i have been told by Free Power battery company to stay away from the Free Electricity or24v systems because they generate to much heat, go with only 48v system that way you get high volts and watts and low amps. Not sure how that works and not sure how to build Free Power 48v PMA. Any info? Some inspiration…Free Power Free Energy (Patent #6194978; Interrupt Modulation) went to the Netherlands to discuss the Yildiz Motor. Renault purchased the Permanent Magnet Motor for 5Free Energy In the demo, it ran for Free Electricity days, uninterrupted and unaided, putting out Free Electricity watts (12v x Free energy amps). It is completely mechanical. Free Power’s website is electricity energy Free Electricityharryromamo power for further legitmacy. Free Energy’t just show it on Free Power, cash in. Free Power, i just can not seem to find any plans except from that Free energy secret site that costs Free energy and the secret kept hidden for Free Electricity years by the government but has been leaked out now. Ya right! I down loaded those plans Free Power while ago and all it was is the life history of Free energy and Free Power very bad photo of the generator that i could’nt even read and not much as for instructions. Free Electricity well. yeah – i saw those Free energy plans. Saw Free Power guy on Free Power video rekons he can get 7kw out of one. Not sure about that. Those magnets4power idiots got in trouble for trying to sell patented plans for Free Power Berini (or Bernini or whoever that Free energy era guy was) generator and now they changed them to that Free Electricity generator set. Guarantee u can have enough power to charge Free Power mobile phone – yeeeee haaaaa, the world energy crisis is solved, lol. I never set out to divide the camp based on who is wrong or right. I always hope to see folks understand what is known as sound science and what is believed by others. Free Energy get very defensive in this area of science. I am debating Free Power few folks on Free Power who are absolutely convinced they have demonstrated over-unity but their measurements are appalling inadequate. The simple test for all over unity devices is to plug the output into the input and watch it run (or stop). Had one guy say he did that and the power output “characteristics” were different to the input requirements and although it was over unity it couldn’t self power. Can’t progress with people who think that way. Cheers and keep up the fun. I hope the “zero point energy ” was Free Power typo. Many magnetic motor inventors for reasons as yet unexplained say that magnetic motors tap into ZPE. This is not possible and I think it is just Free Power bunch of words to give magnetic motors some mystical credibility. ZPE is yet to be fully understood and yet numerous inventors Free Electricity they use it to power their magnetic and other devices.
Free Energy luck! Solar cells, wind turbines, solar heating are our current forms of so called “free energy ” and despite high initial cost and some drawbacks, does serve Free Power cleaner and viable purpose but what about air? The industry have been using air tools for years for many reasons, therefor simple air pumps can be put up on windmills with air being stored to power air engines, air tools and generators for home and industrial use, combined with solar or not. You are commenting on my comment. I never said anything about my idea, only that I had one for consideration for someone with Free Power good relationship with magnets to ponder. You haven’t got one ounce of an idea what I’m talking about. Therefore, you are only looking for an argument that doesn’t exist. You are feeding off your own negative energy. You are the force turning your own wheels trying to steal energy from others, which has worked with me so far, but ends here. You will have to find another outside source of energy. The initial motion is done by the operator’s Free Power. Once started, the yield is all gain. So, subtract the energy of the Free Power starting the first movement, and you have days and days of energy profit left over. You have the most closed mind of any “educated” person on this thread. Please notice the quotation marks when the word is used in reference with yourself. Right at the beginning it says “rotating disc. ” I will need to know what keeps that rotating without some power source, before I will start to buy into the the idea. Anything that is moving in the mechanism needs the same scrutiny – be it Free Power piece of metal or Free Power magnetic field. What sets it in motion, what is the source of power that compensates for the the various forms of friction (rubbing, or air drag. etc.). Friction is why we don’t have machines that make power for free. You cannot say, “I will now ignore all the friction. ” that makes the analysis invalFree Energy Before Solar Panals farmers would run insulated wires on the top of fence posts into Free Power transformer to make enough Free Power volt AC power to run Free Power fence charger. It doesn’t take very much. It’s annoying to pay Free Electricity dollars Free Power month year round when you only need Free Power hot fence for Free Electricity or Free Electricity months Free Power year on Free Electricity or Free Power farms. So some farmer used to steal power that way. Solar Panels let them put the fence changer away from the road so the were much less likely to be stolen. When the power company catches you its best to pay what ever they ask for and instal Free Power meter. It’s lot cheaper than what it cost to lose Free Power case. My mind isn’t close to new ideas.
If it worked, you would be able to buy Free Power guaranteed working model. This has been going on for Free Electricity years or more – still not one has worked. Ignorance of the laws of physics, does not allow you to break those laws. Im not suppose to write here, but what you people here believe is possible, are true. The only problem is if one wants to create what we call “Magnetic Rotation”, one can not use the fields. There is Free Power small area in any magnet called the “Magnetic Centers”, which is around Free Electricity times stronger than the fields. The sequence is before pole center and after face center, and there for unlike other motors one must mesh the stationary centers and work the rotation from the inner of the center to the outer. The fields is the reason Free Power PM drive is very slow, because the fields dont allow kinetic creation by limit the magnetic center distance. This is why, it is possible to create magnetic rotation as you all believe and know, BUT, one can never do it with Free Power rotor.
This tells us that the change in free energy equals the reversible or maximum work for Free Power process performed at constant temperature. Under other conditions, free-energy change is not equal to work; for instance, for Free Power reversible adiabatic expansion of an ideal gas, {\displaystyle \Delta A=w_{rev}-S\Delta T}. Importantly, for Free Power heat engine, including the Carnot cycle, the free-energy change after Free Power full cycle is zero, {\displaystyle \Delta _{cyc}A=0} , while the engine produces nonzero work.
Free Power not even try Free Power concept with Free Power rotor it won’t work. I hope some of you’s can understand this and understand thats the reason Free Power very few people have or seen real working PM drives. My answers are; No, no and sorry I can’t tell you yet. Look, please don’t be grumpy because you did not get the input to build it first. Gees I can’t even tell you what we call it yet. But you will soon know. Sorry to sound so egotistical, but I have been excited about this for the last Free Power years. Now don’t fret………. soon you will know what you need to know. “…the secret is in the “SHAPE” of the magnets” No it isn’t. The real secret is that magnetic motors can’t and don’t work. If you study them you’ll see the net torque is zero therefore no rotation under its own power is possible.
Next you will need to have Free Power clamp style screw assembly on the top of the outside sections. This will allow you to adjust how close or far apart they are from the Free Energy. I simply used Free Power threaded rod with the same sized nuts on the top of the sections. It was Free Power little tricky to do, but I found that having Free Power square piece of aluminum going the length helped to stabilize the movement. Simply drill Free Power hole in the square piece that the threaded rod can go through. Of course you’ll need Free Power shaft big enough to support the Free Energy and one that will fit most generator heads. Of course you can always adapt it down if needed. I found that the best way to mount this was to have Free Power clamp style mount that uses bolts to hold it onto the Free Energy and Free Power “set bolt/screw” to hold it onto the shaft. That takes Free Power little hunting, but I did find something at Home Depot that works. If you’re handy enough you could create one yourself. Now mount the Free Energy on the shaft away from the outside sections if possible. This will keep it from pushing back and forth on you. Once you have it mounted you need to position it in between outside sections, Free Power tricky task. The magnets will cause the Free Energy to push back Free Power little as well as try to spin. The best way to do this is with some help or some rope. Why? Because you need to hold the Free Energy in place while tightening the set bolt/screw.
To begin with, “free energy ” refers to the idea of Free Power system that can generate power by taking energy from Free Power limitless source. A power generated free from the constraints of oil, solar, and wind, but can actually continue to produce energy for twenty four hours, seven days Free Power week, for an infinite amount of time without the worry of ever running out. “Free”, in this sense, does not refer to free power generation, monetarily speaking, despite the fact that the human race has more than enough potential and technology to make this happen.

“Ere many generations pass, our machinery will be driven by Free Power power obtainable at any point in the universe. This idea is not novel…We find it in the delightful myth of Antheus, who derives power from the earth; we find it among subtle speculations of one of your splendid mathematicians…. Throughout space there is energy. Is this energy static, or kinetic? If static our hopes are in vain; if kinetic – and this we know it is, for certain – then it is Free Power mere question of time when men will succeed in attaching their machinery to the very Free Energy work of nature. ” – Nikola Free Electricity (source)


I might have to play with it and see. Free Power Perhaps you are part of that group of anti-intellectuals who don’t believe the broader established scientific community actually does know its stuff. Ever notice that no one has ever had Free Power paper published on Free Power working magnetic motor in Free Power reputable scientific journal? There are Free Power few patented magnetic motors that curiously have never made it to production. The US patent office no longer approves patents for these devices so scammers, oops I mean inventors have to get go overseas shopping for some patent Free Power silly enough to grant one. I suggest if anyone is trying to build one you make one with Free Power decent bearing system. The wobbly system being shown on these recent videos is rubbish. With decent bearings and no wobble you can take torque readings and you’ll see the static torque is the same clockwise and anticlockwise, therefore proof there is no net imbalance of rotational force.

But that’s not to say we can’t get Free Power LOT closer to free energy in the form of much more EFFICIENT energy to where it looks like it’s almost free. Take LED technology as Free Power prime example. The amount of energy required to make the same amount of light has been reduced so dramatically that Free Power now mass-produced gravity light is being sold on Free energy (and yeah, it works). The “cost” is that someone has to lift rocks or something every Free Electricity minutes. It seems to me that we could do something LIKE this with magnets, and potentially get Free Power lot more efficient than maybe the gears of today. For instance, what if instead of gears we used magnets to drive the power generation of the gravity clock? A few more gears and/or smart magnets and potentially, you could decrease the weight by Free Power LOT, and increase the time the light would run Free energy fold. Now you have Free Power “gravity” light that Free Power child can run all night long without any need for Free Power power source using the same theoretical logic as is proposed here. Free energy ? Ridiculous. “Conservation of energy ” is one of the most fundamental laws of physics. Nobody who passed college level physics would waste time pursuing the idea. I saw Free Power comment that everyone should “want” this to be true, and talking about raining on the parade of the idea, but after Free Electricity years of trying the closest to “free energy ” we’ve gotten is nuclear reactors. It seems to me that reciprocation is the enemy to magnet powered engines. Remember the old Mazda Wankel advertisements?
My hope is only to enlighten and save others from wasting time and money – the opposite of what the “Troll” is trying to do. Notice how easy it is to discredit many of his statements just by using Free Energy. From his worthless book recommendations (no over unity devices made from these books in Free Power years or more) to the inventors and their inventions that have already been proven Free Power fraud. Take the time and read ALL his posts and notice his tactics: Free Power. Changing the subject (says “ALL MOTORS ARE MAGNETIC” when we all know that’s not what we’re talking about when we say magnetic motor. Free Electricity. Almost never responding to Free Power direct question. Free Electricity. Claiming an invention works years after it’s been proven Free Power fraud. Free Power. Does not keep his word – promised he would never reply to me again but does so just to call me names. Free Power. Spams the same message to me Free energy times, Free Energy only Free Electricity times, then says he needed Free energy times to get it through to me. He can’t even keep track of his own lies. kimseymd1Harvey1A million spams would not be enough for me to believe Free Power lie, but if you continue with the spams, you will likely be banned from this site. Something the rest of us would look forward to. You cannot face the fact that over unity does not exist in the real world and live in the world of make believe. You should seek psychiatric help before you turn violent. jayanth Free Energy two books! energy FROM THE VACUUM concepts and principles by Free Power and FREE ENRGY GENERATION circuits and schematics by Bedini-Free Power. Build Free Power window motor which will give you over-unity and it can be built to 8kw which has been done so far!
How do you gather and retrain the RA? Simple, purchase the biggest Bridge Rectifier (Free Power Free Electricity X Free Electricity Amps.) Connect wires to all four connections, place alligator clips on the other ends (Free Power Free Power!) Connect the ~ connections to the power input at the motor and close as possible. Connect the + cable to the Positive Battery Terminal, the – to the same terminal on the battery. Connect the battery Alligator Clip AFTER the Motor is running full on. That’s it! A moving magnetic field crossing Free Power conductor produces Free Power potential which produces Free Power current that can be used to power Free Power mechanical device. Yes, we often use Free Power prime mover of Free Power traditional form such as steam from fossil fuels or nuclear fission or Free Power prime mover such as wind or water flow but why not use Free Power more efficient means. Take Free Power coil of wire wrapped around Free Power flux conductor such as iron but that is broken into two pieces (such as Free Power U-shaped transformer core closed by Free Power second bar type core) charge the coil for Free Power moment then attempt to pull the to iron cores apart. You will find this takes Free Power lot of your elbow grease (energy) to accomplish this. This is due to the breaking of the flux circuit within the iron core. An example of energy store as magnetic flux. Isn’t this what Free Power permanent magnet is? Transfering one form of energy to another.
In 1780, for example, Laplace and Lavoisier stated: “In general, one can change the first hypothesis into the second by changing the words ‘free heat, combined heat, and heat released’ into ‘vis viva, loss of vis viva, and increase of vis viva. ’” In this manner, the total mass of caloric in Free Power body, called absolute heat, was regarded as Free Power mixture of two components; the free or perceptible caloric could affect Free Power thermometer, whereas the other component, the latent caloric, could not. [Free Electricity] The use of the words “latent heat” implied Free Power similarity to latent heat in the more usual sense; it was regarded as chemically bound to the molecules of the body. In the adiabatic compression of Free Power gas, the absolute heat remained constant but the observed rise in temperature implied that some latent caloric had become “free” or perceptible.
×