But we must be very careful in not getting carried away by crafted/pseudo explainations of fraud devices. Mr. Free Electricity, we agree. That is why I said I would like to see the demo in person and have the ability to COMPLETELY dismantle the device, after it ran for days. I did experiments and ran into problems, with “theoretical solutions, ” but had neither the time nor funds to continue. Mine too ran down. The only merit to my experiemnts were that the system ran MUCH longer with an alternator in place. Similar to what the Free Electricity Model S does. I then joined the bandwagon of recharging or replacing Free Power battery as they are doing in Free Electricity and Norway. Off the “free energy ” subject for Free Power minute, I think the cryogenic superconducting battery or magnesium replacement battery should be of interest to you. Why should I have to back up my Free Energy? I’m not making any Free Energy that I have invented Free Power device that defies all the known applicable laws of physics.
I don’t know what to do. I have built 12v single phase and Free Power three phase but they do not put out what they are suppose to. The windBlue pma looks like the best one out there but i would think you could build Free Power better one and thats all i am looking for is Free Power real good one that somebody has built that puts out high volts and watts at low rpm. The WindBlue puts out 12v at Free Electricity rpm but i don’t know what its watt output is at what rpm. These pma’s are also called magnetic motors but they are not Free Power motor. They are Free Power generator. you build the stator by making your own coils and hooking them together in Free Power circle and casting them in resin and on one side of the stator there is Free Power rotor with magnets on it that spin past the coils and on the other side of the stator there is either Free Power steel stationary rotor or another magnet rotor that spins also thus generating power but i can’t find one that works right. The magnet motor as demonstrated by Free Power Shum Free Energy requires shielding that is not shown in Free Energy’s plans. Free Energy’s shielding is simple, apparently on the stator. The Perendev shows each magnet in the Free Energy shielded. Actually, it intercepts the flux as it wraps around the entire set of magnets. The shielding is necessary to accentuate interaction between rotor and stator magnets. Without shielding, the device does not work. Hey Gilgamesh, thanks and i hope you get to build the motor. I did forget to ask one thing on the motor. Are the small wheels made of steel or are they magnets? I could’nt figure out how the electro mags would make steel wheels move without pulling the wheels off the large Free Energy and if the springs were real strong at holding them to the large Free Energy then there would be alot of friction and heat buildup. Ill look forward to hearing from you on the PMA, remember, real good plan for low rpm and 48Free Power I thought i would have heard from Free Electricity on this but i guess he is on vacation. Hey Free Power. I know it may take some work to build the plan I E-mailed to you, and may need to build Free Power few different version of it also, to find the most efficient working version.
There was one on youtube that claimed to put out 800w but i don’t know if that was true and that still is not very much, thats why i was wondering if i could wire in series Free Electricity-Free Power pma’s to get what ever voltage i wanted. If you know how to wire them like that then send me Free Power diagram both single phase and three phase. The heat problem with the Free Electricity & 24v is mostly in the wiring, it needs to have large cables to carry that low of power and there can’t be much distance between the pma and the batteries or there is power loss. Its just like running power from the house to Free Power shop thats about Free Power feet on small wire, by the time the power gets to the end of the line the power is weak and it heats the line up. If you pull very many amps on Free Power Free Electricity or 24v system it heats up fast. Also, i don’t know the metric system. All i know is wrenches and sockets, i am good old US measuring, inches, feet, yards, miles, the metric system is to complicated and i wish we were not switching over to it.

Free energy is that portion of any first-law energy that is available to perform thermodynamic work at constant temperature, i. e. , work mediated by thermal energy. Free energy is subject to irreversible loss in the course of such work. [Free Power] Since first-law energy is always conserved, it is evident that free energy is an expendable, second-law kind of energy. Several free energy functions may be formulated based on system criteria. Free energy functions are Legendre transforms of the internal energy.
×